功能丰富 实时交流
移动端访问更便捷
订阅获取更多服务
关注获取更多资讯
实时接收采购订单
本公司位于江苏省扬州市东郊,主要产品用于橡胶,塑料,金属,建筑,电缆,皮革,纺织,医疗,化工等行业.本公司拥有雄厚的设计能力,高素质的员工队伍.”质量为本,用户*”是我公司经营方针,以良好的售后服务立足市场,主要产品有拉力机,压力仪,疲劳试验机,弯曲拉力试验机.磨耗,老化,硬度,可塑性,硫化仪,门尼粘度仪,冲击试验机等测试仪器.我公司一向注重研究开发新产品,并能为您设计制造特殊用途的测试仪器,为产品性能的不断改进和提高作贡献.本公司热忱欢迎新老客户与本厂联系合作!
腾达试验仪器厂:
一、产品简介:
依据行业标准JC482-485-92设计制造的流平性模适用于建筑密封膏的流平性试验取样用。150×20×15mm流平性试模新博乐游戏贴吧下垂度试模建筑密封材料新博乐游戏贴吧。
the product introduction:
The leveling mold designed and manufactured according to the industry standard JC482-485-92 is suitable for the sampling of the leveling test of building sealing paste.150×20×15mm leveling test mold Leveling mold sag test pattern Building sealing material leveling mold.
二、使用方法:
★将试料和模具在5±2oC的低温线内放置30min。
★再模具内衬以0.1mm左右的油纸,油纸四周翻边到模具外,内衬油纸要展平。
★沿模具的一端到另一端注入约20ml的试料,在5±2oC温度下静止放置1h,观察其表面是否平整光滑。
Second,the method of use:
★Place the sample and mold in a low temperature line of 5±2oC for 30min.
★The inner lining of the mold is about 0.1mm oil paper,the oil paper is turned around the mold,and the inner lining oil paper is flattened.
★Inject about 20ml of sample along one end of the mold to the other end,and stand it at 5±2oC for 1h,and observe whether the surface is smooth and smooth.
三、器具构成:
本器具主要由内部尺寸为150*20*15mm的槽体构成。
Third,the appliance composition:
The appliance is mainly composed of a tank having an inner size of 150*20*15 mm.
四、建筑密封材料检测用下垂度试模胶下垂度试模新博乐游戏贴吧
200mm*20mm*10mm
不锈钢铝制
下垂度模具:长度(150±0.2)mm两端开口,其中一端底面延伸(50±0.5)mm,槽的横截面内部尺寸和宽(20±0.2)mm,深(10±0.2)mm。
150*20mm下垂度模具下垂度试模流平性试模下垂度试模挂架建筑密封材料检测用下垂度试模
无气孔且光滑的槽型模具,宜用阳极氧化或非阳极氧化铝合金制成,长度150mm正负0.2mm,两端开口,其中一端底面延伸50mm正负0.5mm,槽的横截面内部尺寸为宽20mm正负0.2mm,深10mm正负0.2mm,其他尺寸的模具也可以实用例如10正负0.2mm,深10正负0.2mm。
Fourth,the construction of sealing materials testing sag test mode rubber sag test mold leveling mold
200mm*20mm*10mm
Stainless steel
Sag mold:length(150±0.2)mm open at both ends,one end of the bottom extends(50±0.5)mm,the internal dimensions of the cross section of the groove and width(20±0.2)mm,deep(10±0.2)mm.
150*20mm sag mold sag test slab leveling test sag sag test slab sag test sag
Non-porous and smooth grooved mold,should be made of anodized or non-anodized aluminum alloy,length 150mm plus or minus 0.2mm,open at both ends,one end of the bottom surface extends 50mm plus or minus 0.5mm,the inner dimension of the cross section of the groove is Width 20mm plus or minus 0.2mm,depth 10mm plus or minus 0.2mm,other sizes of mold can also be practical,for example,10 plus or minus 0.2mm,depth 10 plus or minus 0.2mm.
五、注意事项:
使用完毕后用溶剂擦干净,并干燥后进行保存。
Fourth,note:
After use,wipe with a solvent and dry before storing.
*您想获取产品的资料:
个人信息: