万喜堂彩票最新网址

1.产      品      详      情      资      料：

主要功能•提供一个ControlNet端口（位于TP865基板上的BNC连接器）。•简单的DIN导轨安装。•处理多达31个分布式I/O节点的I/O扫描。•安装在机组底座中的预设两个字母的阿尔法代码锁定装置可防止安装不兼容的组件。•支持热插拔。说明CI865/TP865将ControlNet连接到AC 800M。该模块可以将旧的Satt I/O系统（机架I/O和200系列I/O）与AC 800M控制器平台一起使用，但不能用作通用ControlNet接口。TP865基板有一个用于连接I/O机架的BNC连接器。底板有一个代码锁，见第75页表4，可防止在TP865基板上安装不正确类型的装置。CI865扩展单元包含CEX总线逻辑、ControlNet总线逻辑、CPU和DC/DC转换器，该转换器通过CEX总线从+24 V电源提供适当的电压。R（un）或F（ault）LED均亮起。CI865单元正在配置中。请留出时间以便最终确定。如果情况依然存在，并且CEX总线上的其他单元指示灯未点亮：•检查PM8xx处理器单元内的CEX总线保险丝•启动来自PM8xx处理单元的复位信号（INIT）•更换CI865单元F（故障）指示灯亮起CI865单元正在重新启动过程中。请留出时间以便最终确定。如果情况依然存在，请更换单元。COM A/COM B LED熄灭电源关闭或重置模式COM A/COM B LED呈绿色稳定通道正常COM A/COM乙LED呈绿色闪烁临时错误或需要初始设置COM A/COM丙LED呈红色稳定模块损坏，必须更换COM A/COM丁LED呈红色闪烁坏通道电缆

Key Features • Provides one ControlNet port, (a BNC connector located on the TP865 Baseplate). • Simple DIN-rail mounting. • Handles I/O scanning of up to 31 distributed I/O nodes. • Pre-set, two-letter Alpha code locking device installed in unit base prevents mounting of incompatible components. • Supports Hot swap. Description The CI865/TP865 connects ControlNet to AC 800M. The module makes it possible to use older Satt I/O system (Rack I/O and Series 200 I/O) with the AC 800M controller platform but it can not be used as a general ControlNet interface. The TP865 Baseplate has one BNC connector for connecting I/O racks. The baseplate has a code lock, see Table 4 on page 75, that prevents installation of an incorrect type of unit onto the TP865 Baseplate. The CI865 expansion unit contains the CEX-Bus logic, ControlNet bus logic, CPU and a DC/DC converter that supplies appropriate voltages from the +24 V supply, via the CEX-Bus.Neither R(un) nor F(ault) LED’s are ON The CI865 unit is in the process of being configured. Allow time for this to finalize. If the condition persists, and no other unit LED on the CEX-Bus is lit: • Check the CEX-Bus fuse inside the PM8xx processor unit • Initiate a reset signal (INIT) from the PM8xx processor unit • Replace the CI865 unit F(ault) LED is ON The CI865 unit is in the process of being restarted. Allow time for this to finalize. Replace unit if the condition persists. COM A/COM B LED is OFF Power OFF or Reset Mode COM A/COM B LED is solid green Channel OK COM A/COM B LED is flashing green Temporary error or need initial setup COM A/COM B LED is solid red Module is broken, has to be replaced COM A/COM B LED is flashing red Bad channel cable

2.产      品      展      示

3.公      司      优势     主      营      产      品

4.相关      产     品      展      示

本篇文章出自万喜堂彩票，转载请附上此链接: